WARNING B This product contains lead in solder and certain electrical parts contain chemicals which are known to the state of California to cause cancer, birth defects or other reproductive harm. The following precautions should be observed : 1. When service is required, even though the PDP UNIT an isolation transformer should be inserted between the power line D and the set in safety before any service is performed.
Furthermore where a short circuit has occurred, replace those E components that indicate evidence of overheating. Perform the following precautions for the PDP panel. Pay attention to the following. Charged Section A The places where the commercial AC power is used without passing through the power supply transformer. Power Cord 2. AC Inlet B 3. Power Switch S1 4. High Voltage Generating Point The places where voltage is V or more except for the charged places described above.
Please be sure to confirm and follow these procedures. Product safety Please conform to product regulations such as safety and radiation regulations , and maintain a safe servicing environment by following the safety instructions described in this manual. Use genuine parts. Be sure to use important parts for safety. Soldering should be finished with the proper quantity. Refer to the example 4 Make sure the screws are tightly fastened. Please replace the wiring and cables to the original state after repairs.
In addition, be sure that there are no pinched wires, etc. Please check that neither solder debris nor screws remain inside the product. If you find a damaged power cord, please exchange it with a suitable one. Adjustments To keep the original performance of the products, optimum adjustments and confirmation of characteristics within specification.
Lubricants, Glues, and Replacement parts Use grease and adhesives that are equal to the specified substance. Cleaning For parts that require cleaning, such as optical pickups, tape deck heads, lenses and mirrors used in projection monitors, proper cleaning should be performed to restore their performances. Shipping mode and Shipping screws. Be careful not to tighten them in the wrong order forcibly. If you tighten the screws too tightly with an electric screwdriver, the screw heads may be damaged, in Audio Blue 5 1 Enter the Standby mode.
A: Let the panel sit at least for 3 minutes after the power is turned off. For details, see " Some boards need settings made after replacement of the Assys. Note 1 : Use a remote control unit supplied with the 6th-generation models or later.
Note 2 : Do not hold a key pressed for more than 5 seconds. After entering Factory mode, press [«] three times. How to display the Mask indication 1 Mask indication in the panel side 1. Adjustments and Settings after replacement of the Assys Procedures in Factory mode 1. Mode transition in Service Factory mode.
Structure of Layers in Panel Factory Mode 1 1. X-SUS B 2. Home Theater Server Manuals. Home Theater System Manuals. Indoor Furnishings Manuals. Insulin Pen Manuals. Kitchen Entertainment Center Manuals.
Life Jacket Manuals. Marine Radio Manuals. Medical Alarms Manuals. Metal Detector Manuals. MiniDisc Player Manuals. Mixer Manuals. Mobility Aid Manuals. Model Vehicle Manuals. Make sure the proper amount is applied. Shipping mode and Shipping screws To protect products from damages or failures during transit, the shipping mode should be set or the shipping screws should be installed before shipment. Please be sure to follow this method especially if it is specified in this manual.
For details, refer to "Important Check Points for good servicing". This service manual is intended for qualified service technicians ; it is not meant for the casual. Qualified technicians have the necessary test equipment and tools, and have been. Improperly performed repairs can adversely affect the safety and reliability of the product and may. If you are not qualified to perform the repair of this product properly and safely,. This product contains lead in solder and certain electrical parts contain chemicals which are known to the state of California to.
The following precautions should be observed :. When replacing a chassis in the set, all the protective devices. Especially critical components as indicated on the circuit. Furthermore where a short circuit has occurred, replace those. Before returning a serviced set to the customer, the service. Therefore, the following checks should be. Perform the following precautions against unwanted radiation.
Shield Case etc. Check that the. Twisting or pulling the FPC when connecting it to the. TVs and radios in the surrounding. With the AC plug removed from an AC power source, place a. Using an insulation tester DC V , connect one lead to the. Exposed metal parts having a return path to. Exposed metal parts not having a return path to. Plug the AC line cord directly into an AC power source do not.
These are often not evident. Replacement parts which. Do not defeat the. This digital television is capable of receiving analog. A security card. Certain advanced and. For more information call your. When installing this unit, make sure to leave space. For the minimum space required, see page. This Class B digital apparatus complies with Canadian. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference, and.
Product Name: Plasma Display System. When placed into the standby mode, the main power flow is cut and the unit is no longer. However, the. Plasma Display system will still consume some power as long as the power cord is.
These limits are designed to provide reasonable protection against harmful. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in. However, there is. If this equipment does cause harmful. To prevent electromagnetic interference with electric appliances such as radios and.
The mains plug of unit. Operating environment temperature and humidity:. Thank you for buying this Pioneer product. After you have finished. In some countries or regions, the shape of the power plug and power outlet may sometimes differ from that shown in the. Speaker accessories Plasma Display Remote control unit Installing the Plasma Display Moving the Plasma Display When using the hung on wall unit Preventing the Plasma Display from.
Falling Over Cable connections for watching digital. Switching between antenna A and B Preparing the remote control unit Inserting batteries Cautions regarding batteries Allowed operation range of the remote. Cautions regarding the remote control. Connecting the power cord Routing cables Turning on the power Turning off the power Watching TV channels Selecting the antenna Changing channels Changing the volume and sound Changing the language
0コメント